Determination of the Elemental Iodine in Human Breast Milk by Inductively Coupled Plasma mass Spectrometry.

Adequate iodine status in lactating women is defined by a maternal median urinary iodine concentration (UIC) ≧ 100 µg/L. However, the above-mentioned criterion does not account for the secretion of iodine into breast milk and could not truly reflect the amount of iodine delivered to the infants. Measuring breast milk median iodine concentration (BMIC) is crucial, but the method to measure BMIC has not been developed and validated in Taiwan. We adopted the ammonia dilution method without prior sample digestion to measure BMIC by inductively coupled plasma mass spectrometry (ICP-MS). Samples and iodate calibrators were prepared into an aqueous solution containing Triton X-100, 0.5% ammonia solution, and tellurium (128Te) as the internal standard. Precision, accuracy, serial dilution, and recovery tests were performed for method validation. The range of intra-assay and inter-assay coefficient of variation for the four human breast milk samples with different iodine concentrations were 3.2-4.7% and 2.3-5.5%, respectively. The standard NIST 1549 milk powder was prepared into three different concentrations of 50 µg/L, 100 µg/L, and 200 µg/L to assess the accuracy; the bias was < 5%. A recovery of 95-105% was achieved for four human breast milk samples spiked with sodium iodide solution. The serial dilution test confirmed linearity up to 0.998. The limit for detection and quantification was 0.78 µg/L and 2.34 µg/L, respectively. The results of the current study confirmed that this ICP-MS method is accurate and reliable in measuring BMIC.

Influence of short-lived radioiodines other than 131I on screening direct thyroid measurements with TCS-172 NAI(TL) survey meters.

In a nuclear emergency, one of the actions taken for the sake of public is to monitor thyroid exposure to radioiodines. Japan's Nuclear Regulation Authority recently published a report on such monitoring and proposed direct thyroid measurements with conventional NaI(Tl) survey meters (e.g. Hitachi model TCS-172) as a primary screening method. A previous study proposed screening levels (SLs) used in these simplified measurements as the net reading values of the TCS-172 device. Age-specific SLs were derived from a thyroid equivalent dose of 100 mSv due to the inhalation intake of 131I. This study addressed the possible influence of short-lived iodine isotopes other than 131I on the simplified measurements. In preparation for such measurements, the responses of the device for 132I as an ingrowth component from 132Te, 133I, 134I and 135I in the thyroid were evaluated by numerical simulations using age-specific stylized phantoms in addition to those obtained for 131I in the previous study. The radioactivity ratios of the relevant isotopes were taken from the inventory data of the Fukushima Daiichi Nuclear Power Plant. The results were used to predict the net readings of the device when 132Te-132I and 133I as well as 131I were inhaled at 24 or 72 h after the shutdown of a nuclear power plant. In these cases, the signals from 132Te-132I and 133I become undetectable a couple of days after intake, which could lead to underestimations of the thyroid dose. To estimate the thyroid dose accurately from the simplified measurements, it is necessary to identify the exact time of intake after the shutdown and the actual physiochemical property of 132Te that affects the thyroid uptake of 132I.

Exposure to the Thyroid from Intake of Radioiodine Isotopes after the Chornobyl Accident. Report I: Revised Doses and Associated Uncertainties for the Ukrainian-American Cohort.

Thyroid doses from intake of radioiodine isotopes (131I, 132Te+132I, and 133I) and associated uncertainties were revised for the 13,204 Ukrainian-American cohort members exposed in childhood and adolescence to fallout from the Chornobyl nuclear power plant accident. The main changes related to the revision of the 131I thyroid activity measured in cohort members, the use of thyroid-mass values specific to the Ukrainian population, and the revision of the 131I ground deposition densities in Ukraine. Uncertainties in doses were assessed considering shared and unshared errors in the parameters of the dosimetry model. Using a Monte-Carlo simulation procedure, 1,000 individual stochastic thyroid doses were calculated for each cohort member. The arithmetic mean of thyroid doses from intake of 131I, 132Te+132I, and 133I for the entire cohort was 0.60 Gy (median = 0.22 Gy). For 9,474 subjects (71.6% of the total), the thyroid doses were less than 0.5 Gy. Thyroid doses for 42 cohort members (0.3% of the total) exceeded 10 Gy while the highest dose was 35 Gy. Intake of 131I contributed around 95% to internal thyroid exposure from radioiodine isotopes. The geometric standard deviation of individual stochastic thyroid doses varied among cohort members from 1.4 to 4.3 with an arithmetic mean of 1.6 and a median of 1.4. It was shown that the contribution of shared errors to the dose uncertainty was small. The revised thyroid doses resulted, in average, in around 40% decrease for cohort members from Zhytomyr Oblast and an increase of around 24% and 35% for the cohort members from Kyiv and Chernihiv Oblast, respectively. Arithmetic mean of TD20 doses for the cohort was around 8% less than that estimated in TD10, 0.60 Gy vs. 0.65 Gy, respectively; however, global median of TD20 doses somewhat increased compared to TD10: 0.22 Gy vs. 0.19 Gy, respectively. The difference between TD10 and TD20 was mainly due to a revision of the individual 131I thyroid activity measured in the cohort members.

Assessment of internal exposure to 131I and short-lived radioiodine isotopes and associated uncertainties in the Ukrainian cohort of persons exposed in utero.

This study revised the thyroid doses for 2582 Ukrainian in utero cohort members exposed to Chornobyl fallout (the Ukrainian in utero cohort) based on revision of: (i) 131I thyroid activity measured in the Ukrainian population, (ii) thyroid dosimetry system for entire Ukraine, and (iii) 131I ground deposition densities in Ukraine. Other major improvements included: (i) assessment of uncertainties in the thyroid doses considering shared and unshared error, and (ii) accounting for intake of short-lived radioisotopes of tellurium and iodine (132Te+132I and 133I). Intake of 131I was the major pathway for thyroid exposure, its median contribution to the thyroid dose was 97.4%. The mean prenatal and postnatal thyroid dose from 131I was 87 mGy (median = 17 mGy), higher than previous deterministic dose of 72 mGy (median = 12 mGy). For 39 individuals (1.5%) the dose exceeded 1.0 Gy, while the highest dose among the cohort members was 2.7 Gy. The geometric standard deviation (GSD) of 1000 individual stochastic doses varied from 1.9 to 5.2 with a mean of 3.1 and a median of 3.2. The lowest uncertainty (mean GSD = 2.3, median GSD = 2.2) was found for the subjects whose mothers were measured for 131I thyroid activity, while for individuals, whose mothers were not measured, the mean and median GSDs were 3.4. Uncertainties in thyroid doses were driven by shared errors associated with the parameters of the ecological model.

Characterisation of selenium and tellurium nanoparticles produced by Aureobasidium pullulans using a multi-method approach.

Aureobasidium pullulans was grown in liquid culture media amended with selenite and tellurite and selenium (Se) and tellurium (Te) nanoparticles (NPs) were recovered after 30 d incubation. A separation method was applied to recover and characterise Se and Te NPs by asymmetric flow field flow fractionation (AF4) with online coupling to multi-angle light scattering (MALS), ultraviolet visible spectroscopy (UV-Vis), and inductively coupled plasma mass spectrometry (ICP-MS) detectors. Additional characterisation data was obtained from transmission electron microscopy (TEM), and dynamic light scattering (DLS). Solutions of 0.2% Novachem surfactant and 10 mM phosphate buffer were compared as mobile phases to investigate optimal AF4 separation and particle recovery using Se-NP as a model sample. 88% recovery was reported for 0.2% Novachem solution, compared with 50% recovery for phosphate buffer. Different crossflow (Cflow) rates were compared to further investigate optimum separation, with recoveries of 88% and 30% for Se-NPs, and 90% and 29% for Te-NPs for 3.5 mL min-1 and 2.5 mL min-1 respectively. Zeta-potential (ZP) data suggested higher stability for NP elution in Novachem solution, with increased stability attributed to minimised NP-membrane interaction due to PEGylation. Detection with MALS showed monodisperse Se-NPs (45-90 nm) and polydisperse Te-NPs (5-65 nm).Single particle ICP-MS showed mean particle diameters of 49.7 ±â€¯2.7 nm, and 135 ±â€¯4.3 nm, and limit of size detection (LOSD) of 20 nm and 45 nm for Se-NPs and Te-NPs respectively. TEM images of Se-NPs and Te-NPs displayed a spherical morphology, with the Te-NPs showing a clustered arrangement, which suggested electrostatic attraction amongst neighbouring particles. Particle hydrodynamic diameters (dH) measured with dynamic light scattering (DLS) further suggested monodisperse Se-NPs and polydisperse Te-NPs distributions, showing good agreement with AF4-MALS for Se-NPs, but suggests that the Rg obtained from AF4-MALS for Te-NP was unreliable. The results demonstrate a complementary application of asymmetric flow field-flow fractionation (AF4), ICP-MS, light scattering, UV-Vis detection, and microscopic techniques to characterise biogenic Se and Te NPs.

Determination of l-theanine in tea water using fluorescence-visualized paper-based sensors based on CdTe quantum dots/corn carbon dots and nano-porphyrin with chemometrics.

BACKGROUND: The quality of tea is influenced by numerous factors, especially l-theanine, which is one of the important markers used to evaluate the sweetness and freshness of tea. Sensitive, rapid, and accurate detection of l-theanine is therefore useful to identify the grade and quality of tea. RESULTS: A high-sensitivity, paper-based fluorescent sensor combined with chemometrics was established to detect l-theanine in tea water based on CdTe quantum dots / corn carbon dots and nano tetra pyridel-porphine zinc (ZnTPyP). To verify the reliability of this method, fluorescence spectra and fluorescence-visualized paper-based sensors were compared. The fluorescence spectrum method demonstrated a linear range of 1 to 10 000 nmol L-1 and a limit of detection (LOD) of 0.19 nmol L-1 . In the fluorescence-visualized paper-based sensors there was a linear range of 10-1000 nmol L-1 , and the LOD was 10 nmol L-1 . Partial least squares discriminant analysis (PLSDA) and partial least squares regression analysis (PLSR) were used successfully to determine l-theanine accurately in tea water with this approach. The accuracy of the PLSDA model was 100% both in the training set and the predicting set, and the correlation coefficient between the actual concentration and the predicted concentration was greater than 0.9997 in the PLSR model. CONCLUSION: This fluorescence-visualized paper-based sensor, combined with chemometrics, could be applied efficiently to the practical analysis of tea water samples, which provides a new idea to ensure the flavor and quality of tea. © 2020 Society of Chemical Industry.

Elucidation of tellurium biogenic nanoparticles in garlic, Allium sativum, by inductively coupled plasma-mass spectrometry.

BACKGROUND: Biosynthesis of Te nanoparticles may occur in higher plants exposed to Te, as reported on microorganisms. However, unambiguous observations of the biogenic nanoparticles (BgNPs) of Te in plants are lacking. Hence, in this study, we investigated the formation of insoluble BgNPs of Te in garlic (Allium sativum) as a model plant. METHOD: We performed elemental analysis based on inductively coupled plasma-mass spectrometry (ICP-MS) technique, and obtained Te concentration and distribution in various parts of garlic. In addition, insoluble Te particles were detected by fast time-resolved ICP-MS. Direct observation of the insoluble Te particle was also conducted by scanning electron microscope (SEM) and transmission electron microscope (TEM). RESULTS: A part of the roots and clove from Te-exposed garlic showed black coloration. Te concentrations in the black-colored parts were significantly increased compared with the non-colored parts. Transient signals of Te unique to nanoparticles were detected from the insoluble fractions of the black-colored parts. Finally, rod-shaped biogenic Te nanoparticles consisting of highly crystalline elemental Te was observed by SEM and TEM. CONCLUSION: Our data provide new insights to the metabolic pathway of Te in higher plants for the formation of insoluble biogenic nanoparticles, which is extremely important for the detoxification of Te.

Triple-sensitivity high-spatial-resolution X-ray computed tomography using a cadmium-telluride detector and its beam-hardening effect.

To observe blood vessels at high contrasts, we constructed a first-generation triple-sensitivity X-ray computed tomography (TS-CT) scanner using a cadmium-telluride (CdTe) detector and a triple-amplifying system. X-ray photons are absorbed by the CdTe crystal, and the electric charges produced by photons are converted into voltages using a current-to-voltage (I-V) amplifier, and the I-V output is amplified by a voltage-to-voltage (V-V) amplifier. The V-V output 1 is sent to a dual V-V amplifier through a 5.0-m-length coaxial cable and amplified to two-different outputs of 2 and 3. The three outputs 1-3 are sent to a personal computer through an analog-to-digital converter to reconstruct three tomograms simultaneously. In the TS-CT, the scattering photons from the object are extremely reduced using a 0.5-mm-diameter lead pinhole behind the object. The translation and rotation steps were 0.1 mm and 0.5°, respectively, and the spatial resolutions were 0.25 × 0.25 mm2. The scanning time was 19.6 min, and blood vessels were visible using gadolinium contrast media. In particular, the effective photon energy increased with increasing amplification factor of the amplifier caused by beam hardening of the object.

Precise Measurement of Tellurium Isotope Ratios in Terrestrial Standards Using a Multiple Collector Inductively Coupled Plasma Mass Spectrometry.

Precise tellurium (Te) isotope ratio measurement using mass spectrometry is a challenging task for many decades. In this paper, Te isotope ratio measurements using multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS) in terrestrial Te standards have been reported. Newly developed Faraday cup with 1012 Ω resistor is used to measure low abundance 120Te, whereas the 1011 Ω resistor is used to measure other Te isotopes. The relative standard deviation obtained for Te isotope ratio measurement by Faraday cups of 120Te/128Te [0.002907(05)], 122Te/128Te [0.079646(10)], 123Te/128Te [0.027850(07)], 125Te/128Te [0.221988(09)], 126Te/128Te [0.592202(20)], and 130Te/128Te [1.076277(30)] were 0.140%, 0.014%, 0.026%, 0.005%, 0.004%, and 0.004%, respectively. The measured isotope ratio results are compared with previous results obtained by thermal ionization mass spectrometry (TIMS), negative thermal ionization mass spectrometry (N-TIMS), and MC-ICP-MS, showing an improvement in the precision about one order of magnitude for 120Te/128Te ratio. The present study shows better precision for Te isotope ratios compared to earlier studies.

Structural and electrochemical characterization of lawsone-dependent production of tellurium-metal nanoprecipitates by photosynthetic cells of Rhodobacter capsulatus.

Cells of the facultative photosynthetic bacterium Rhodobacter capsulatus exploit the simultaneous presence in the cultural medium of the toxic oxyanion tellurite (TeO32-) and the redox mediator lawsone (2-hydroxy-1,4-naphthoquinone) by reducing tellurite to metal Te0 nanoprecipitates (TeNPs) outside the cells. Here we have studied the mechanism by which lawsone interacts with metabolically active cells and analysed both structure and composition of the TeNPs collected from the growth medium of phototrophycally grown R. capsulatus. High Resolution Transmission Electron Microscopy (HR-TEM) images and Energy-Dispersive X-ray (EDX) microanalysis of TeNPs showed a central core of polycrystalline tellurium interspersed in an organic matrix with a predominant protein-based composition. The main proteins from Te0 nanostructures were identified by Liquid Chromatography tandem-Mass Spectrometry and were all correlated with the cell outer membrane composition. The interaction of reduced lawsone with tellurite and with the bacterial cells was probed by Cyclic Voltammetry and Scanning ElectroChemical Microscopy (SECM). We concluded that lawsone is required for the reduction of tellurite to metal Te0 in a reaction mechanism dependent on reducing equivalents deriving from the cell photosynthetic metabolism. SECM experiments demonstrate that lawsone, by diffusing inside the bacterial cells, is effectively available at the membrane site of the photosynthetic electron transport chain.

Optimization of T-shape slotted quartz tube with exit holes-atom trap-flame atomic absorption spectrophotometry system for the accurate and sensitive determination of tellurium in tap water.

Tellurium has been widely used in industrial processes and daily life products, and can cause serious health problems upon exposure. Therefore, determination of tellurium in real-life samples is very crucial. In this study, an accurate, environmentally friendly, and inexpensive analytical method was developed to determine trace levels of tellurium in water samples. To lower the detection limits, system parameters including flame type, acetylene flow rate, slotted quartz tube (T-SQT) height, and trapping period were optimized. Under the optimum conditions, the limit of detection (LOD) and quantification (LOQ) were calculated as 14.1 ng/mL and 47.1 ng/mL, respectively. For recovery studies, the optimized T-SQT-AT-FAAS method was applied to tap water samples to determine trace levels of tellurium and recovery results were found between 91.1 and 111.3%. Relative standard deviation value (%RSD) of the developed method was found to be less than 5.0% even for the lowest concentration in calibration plot, specifying good accuracy and high applicability of the method for water samples. Graphical abstract .

Magnetic cobalt particle-assisted solid phase extraction of tellurium prior to its determination by slotted quartz tube-flame atomic absorption spectrophotometry.

The emergence of magnetic materials has opened up doors to numerous applications including their use as sorbents for preconcentration of trace elements. Magnetic materials exhibit many unique advantages in sample preparation such as easy separation from the sample, high preconcentration factor, and short operation period. In the present study, magnetic cobalt material was synthesized, characterized, and used as an effective sorbent in a solid phase extraction process. Experimental variables of the extraction process including pH and volume of buffer solution, eluent concentration and volume, mixing type and period, and sorbent amount were optimized to achieve maximum extraction efficiency. Instrumental variables of flame atomic absorption spectrophotometry and the type of slotted quartz tube were also investigated. Under the optimum conditions, the combined method provided a wide linear range between 50 and 200 ng/mL with detection and quantification limits of 15.4 ng/mL and 51.3 ng/mL, respectively. Relative standard deviations of the proposed method were less than 5.0% and a high enrichment factor of 86.7 was obtained. The proposed method was successfully applied to soil samples for the determination of trace tellurium.

Tellurium behaviour in the Fukushima Dai-ichi Nuclear Power Plant accident.

The behaviour of tellurium radionuclides in the Fukushima Dai-ichi Nuclear Power Plant accident was examined to determine if it is consistent with the current understanding of tellurium chemistry, and whether there is any evidence of tellurium dispersal by species other than aerosols (e.g., vapours). Previous speciation studies, hot-cell experiments, in-reactor experiments and the transport from the Chernobyl reactor accident indicated that tellurium would behave primarily as a particulate species that condensed at high temperature, although the initial chemical species may have transformed to other solid species on cooling and reaction with environmental compounds (e.g., air). The main volatile tellurium species expected would be organic tellurides, which could be produced by radiolytic or biochemical routes, and have reasonable stability under environmental conditions. The behaviour of 137Cs, which behaves exclusively as a particulate species in air at environmental temperatures, was compared with that of tellurium. The behaviour of tellurium was found to be consistent with the current understanding and no evidence of significant tellurium transport by vapour species was found.

Cytotoxicity studies of quantum dots with the electroporation method.

In this study, the cytotoxicity of CdTe quantum dots (QDs) of various dimensions was examined using the electroporation method. The influence of the size of QDs on normal and tumour cell viability after 24 h of incubation with nanomaterials was examined. The three human cell lines were chosen for the tests: A549 (a tumour cell line derived from the lung), MRC-5 (normal fibroblasts from the lung) and HaCaT (normal keratinocytes from the skin). Accordingly, we modelled the effect of nanocrystals on various human tissues because nanoparticles can be introduced into an organism through different routes. We were also able to study which cells are more sensitive to nanoparticles: normal or tumour cells. The nanoparticles were introduced into cells through pores in the cell membranes that were generated by electrical pulses. The effectiveness of introducing nanocrystals into cells was determined as a function of the nanocrystal dimensions and accumulation locations. Moreover, the cytotoxicity of quantum dots was tested, and cell viability after electroporation was evaluated. We also investigated whether the introduced nanocrystals released cadmium ions.

Study of CdTe detection efficiency for medical applications using Geant4-based stochastic simulations.

The determination of detection efficiency and peak-to-total ratios has been performed for rectangular CdTe detectors for various x-ray and low-energy γ-ray source configurations including parallel beams, point, and cylindrical sources. The dependence of efficiency values on axial and off-axial distances, detector thickness and area, and source dimensions has been studied. The detector model developed in this work has been validated by comparing the Monte Carlo simulated values of detector efficiency for a parallel incident beam with the available published data and good agreement has been found with discrepancies remaining within 2% throughout the energy range. Geant4 simulations show nearly 100% photopeak and total efficiency with peak-to-total ratios approaching a maximum value of 1.0 for photons in the 4-70 keV energy range. Similar high values of detection efficiency have been obtained for brachytherapy I-125 seed sources having cylindrical geometries which indicates the suitability of CdTe detectors for the calibration of sources used in therapy. The logistic power curve was found excellent for empirically fitting the photopeak efficiency variations with axial displacement of the I-125 brachy source in the horizontal configuration. Geant4 simulations clearly show that small thicknesses, of the order of 0.5 mm, of CdTe material are sufficient for attaining almost 100% detection efficiency for low-energy photons having energies up to 100 keV.

Total content and in vitro bioaccessibility of tellurium in Brazil nuts.

Alongside the Brazil nut's role as an excellent source of vitamins, oil, fatty acids, lipids and nutrients, it is also recognized as a rich source of selenium. The pathway along which selenium and sulfur are metabolized in plants is theorized to be the same as that used for tellurium. Total tellurium content and its bioaccessibility are then evaluated by ICP-MS. Interferences and sample preparation are evaluated for the accurate determination of tellurium, and the accuracy determined through analysis of the certified reference material 1643e. A concentration of 4.02 ±â€¯0.391 ng g-1 is obtained as an average concentration through external and internal calibrations. Through this reliable result, tellurium bioaccessibility in Brazil nuts is obtained via an in vitro validated unified bioaccessibility method. Values of 32% and 30% of total tellurium are available in the gastric and gastrointestinal fractions, respectively.

Evaluation of the Content of Antimony, Arsenic, Bismuth, Selenium, Tellurium and Their Inorganic Forms in Commercially Baby Foods.

Baby foods, from the Spanish market and prepared from meat, fish, vegetables, cereals, legumes, and fruits, were analyzed to obtain the concentration of antimony (Sb), arsenic (As), bismuth (Bi), and tellurium (Te) as toxic elements and selenium (Se) as essential element. An analytical procedure was employed based on atomic fluorescence spectroscopy which allowed to obtain accurate data at low levels of concentration. Values of 14 commercial samples, expressed in nanograms per gram fresh weight, ranged for Sb 0.66-6.9, As 4.5-242, Te 1.35-2.94, Bi 2.18-4.79, and Se 5.4-109. Additionally, speciation studies were performed based on data from a non-chromatographic screening method. It was concluded that tellurium and bismuth were mainly present as inorganic forms and selenium as organic form, and antimony and arsenic species depend on the ingredients of each baby food. Risk assessment considerations were made by comparing dietary intake of the aforementioned elements through the consumption of one baby food portion a day and recommended or tolerable guideline values.

Biology and toxicology of tellurium explored by speciation analysis.

Tellurium (Te) is widely used in industry because it has unique physicochemical properties. Although Te is a non-essential element in animals and plants, it is expected to be metabolized to organometallic compounds having a carbon-Te bond in living organisms exposed to inorganic Te compounds. Thus, the speciation and identification of tellurometabolites are expected to contribute to the depiction of the metabolic chart of Te. Speciation by elemental mass spectrometry and identification by molecular mass spectrometry coupled with separation techniques have significantly contributed to the discovery of tellurometabolites in animals and plants. The aim of this mini review is to present recent advances in the biology and toxicology of tellurium as revealed by speciation and identification by molecular mass spectrometry.

Simultaneous speciation of inorganic arsenic, selenium and tellurium in environmental water samples by dispersive liquid liquid microextraction combined with electrothermal vaporization inductively coupled plasma mass spectrometry.

A new method based on dispersive liquid liquid microextraction (DLLME) combined with electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) was developed for the simultaneous speciation of inorganic arsenic (As), selenium (Se) and tellurium (Te) with sodium diethyldithiocarbamate (DDTC) as both chelating reagent and chemical modifier. As(III), Se(IV) and Te(IV) were transformed into DDTC-chelates at pH 7 and extracted into the fine droplets formed by injecting the binary solution of bromobenzene (extraction solvent) and methanol (dispersive solvent) into the sample solution. After phase separation by centrifugation, As(III), Se(IV) and Te(IV) preconcentrated in the organic phase were determined by ETV-ICP-MS. Total inorganic As, Se and Te were obtained by reducing As(V), Se(VI) and Te(VI) to As(III), Se(IV) and Te(IV) with L-cysteine, which were then subjected to the same DLLME-ETV-ICP-MS process. The concentration of As(V), Se(VI), Te(VI) were calculated by subtracting the concentration of As(III), Se(IV) and Te(IV) from the total inorganic As, Se and Te, respectively. The main factors affecting the microextraction efficiency and the vaporization behavior of target species were investigated in detail. Under the optimal conditions, the limits of detection were 2.5, 8.6 and 0.56 ng L(-1) for As(III), Se(IV) and Te(IV), respectively, with the relative standard deviations (n=7) of 8.5-9.7%. The developed method was applied to the speciation of inorganic As, Se and Te in Certified Reference Materials of GSBZ50004-88, GBW(E)080395 and GBW(E)080548 environmental waters, and the determined values are in good agreement with the certified values. The method was also successfully applied to the simultaneous speciation of inorganic As, Se and Te in different environmental water samples with the recoveries in the range of 86.3-107% for the spiked samples.

Characterization of a rapid and reliable method for iodide biomonitoring in serum and urine based on ion chromatography-ICP-mass spectrometry.

An appropriate and controlled supply of thyroid hormones is vital for proper body function. In turn, an appropriate synthesis of T3 and T4 in the thyroid gland is dependent on a sufficient and balanced iodide concentration in blood serum. Due to widespread iodine deficiency or some cases of iodine over exposure, iodide biomonitoring in serum is important and it is that biomonitoring approach being closest to the bioavailable I(-) supply for the thyroid gland. Therefore, this paper describes a biomonitoring method for iodide determination in serum based on ion chromatography-inductively coupled plasma mass spectrometry (IC-ICP-MS). Since in literature only very few data are available on iodide in serum but many in urine the method is also extended to I(-) monitoring in urine. The method was additionally designed to have short analysis time (8min) for increased sample throughput, good precision in serial measurement (serum: 4.86%; urine: 1.4%), and day-to-day determination (serum: 5.7%; urine: 2.28%), high accuracy (serum: 105%; urine: 101%) and good recovery (serum: 102%; urine: 99%) even in matrix-rich samples at low I(-) concentration. Also, investigations were performed to elucidate whether internal standardization during chromatography, sample preparation for protein-matrix removal or matrix-matched calibration are advantageous for analytical performance. Finally, limits of detection (3σ) of 0.12µg/L or 0.05µg/L (serum or urine) and limit of quantification (10σ) of 0.39µg/L or 0.17µg/L (serum or urine) were achieved.